Diccoplast 80

Diccoplast 80
ОПИС A two component acid catalysed paint.

 A fast drying, durable paint with good filling properties for indoor use.

Перпорачана употреба Suitable for furniture, doors and other wooden and fibre board surfaces.

Features The product has MED (Marine Equipment Directive) certificate no
VTT-C-4032-15-09 and is thus accepted for painting surfaces inside the ships.
Палета на бои Special colour white 201.
Colour Cards RAL, NCS, SSG, BS, MONICOLOR NOVA and SYMPHONY colour cards. TEMASPEED PREMIUM tinting.
Gloss groups Gloss
Emission classification The emission level of this product fulfils the requirements of E1 classification for surface treatment materials. The product has been tested according to the standard EN 717-1, and its formaldehyde emission rate is less than 0.124 mg/m3 air.

Recommended spreading amounts (unthinned)

Theoretical coverage




45–55 µm

100–120 g/m2

11–12 m2/l


Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.
Разредувач 1027 and 1033
Mixing ratio Paint 100 parts by volume 634-serie
Hardener 10 parts by volume 006 2098
Метод на примена

Air assisted airless and conventional spraying.


Air assisted airless application with the viscosity 25–50 s (DIN 4) can be reached with approximately 5–20 % of thinning. Nozzle tip 0.011"–0.015" and the nozzle pressure

40–140 bar. Atomising air pressure should be about 1–3 bar. Spray angle shall be chosen according to the shape of the object.


Conventional application with the viscosity 20–25 s (DIN 4) can be reached with approximately 10–20 % thinning. Nozzle tip 1.4–1.8 mm and the nozzle pressure

 2–3 bar.

Pot-life (+23°C) 48 hours.
Drying times

100–120 g/m²

+23 ºC

+50 ºC

Dry to touch, after

20–30 min

10–20 min

Dry to stack, after

4–6 h

40–60 min

Dry to pack, after

1 d

1–2 h


Stacking temperature below +35 ºC.


Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.

Содржина на цврсти материи 58±2 % by volume
69±2 % by weight
Густина 1.3 kg/l
Шифра на производот 634 series
MED Certificate VTT-C-4032-15-09 Diccoplast 30

Услови за примена The surface to be painted has to be clean and dry. During application and drying the temperature of the air, the surface to be treated and the paint has to be over 18ºC and the relative humidity of the air below 70%.
Припрема Wood surface must be sanded with sanding paper P150–240. Sanding between primer and top coat can be done with sanding paper P240–400. All sanding dust must be removed before painting.
Priming Diccoplast Primer and Diccoplast Plus Tix.
Mixing of components Stir the paint carefully before use. Add 10 volume % of Hardener 006 2098, Hardener 006 2093 or Hardener 006 2096. Thin the paint to the viscosity required with Thinner 1027 or 1033.

Do not use iron containers as mixing container. Instead use plastic, enamel or acid resistant steel containers.
Чистење на алатот Thinner 1027, 1025 or 1033.
EU VOC 2004/42/EC ограничена вредност The Volatile Organic Compounds amount is 390 g/litre of paint mixture.
VOC content of the paint mixture (thinned 20 % by volume) is 450 g/l.
VOC 2004/42/EC (catA/j) 500 g/l (2010)

во согласност со Регулативата (EC) No. 1272/2008
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj. For industrial and professional use only.
Safety data sheetDICCOPLAST 30 [GB-ENG]
Thinner safety data sheetTHINNER 1033 [GB-ENG]
Hardener safety data sheetHARDENER 006 2098 [GB-ENG]