ТЕХНИЧКИ ЛИСТ
05.12.2013

Diccoplast Elastic Primer

 
Diccoplast Elastic Primer
ОПИС A two component acid catalysed primer.
КАРАКТЕРИСТИКИ НА ПРОИЗВООДОТ

A fast drying paint for interior and exterior use.

Good filling and sanding properties. Gives an elastic film.

Перпорачана употреба Recommended for exterior doors, furniture and MDF-boards.

ТЕХНИЧКИ ПОДАТОЦИ
Палета на бои White 0201.
Gloss groups Matt
Emission classification Emission levels of this paint fulfils the E1-classification. Paint has been tested according to EN 717-1, and formaldehyde emission is less than 0.124 mg/m3 air.
Покривност

Recommended spreading amounts (unthinned)

Theoretical coverage

dry

wet

 

40–50 µm

100–120 g/m2

11–14 m2/l

 

Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.

Разредувач 1027 and 1033
Mixing ratio Paint 100 parts by volume 691-series
Hardener 10 parts by volume 006 2098
Метод на примена

Airless spraying, air assisted airless spraying and conventional spraying.

 

Application (+23 °C)

Airless application with the viscosity 25–50 s (DIN 4) can be reached with approximately 5–20 % of thinning. Nozzle tip 0.011"–0.015" and the nozzle pressure 80–180 bar. Spray angle shall be chosen according to the shape of the object.

 

Air assisted airless application with the viscosity 25–50 s (DIN 4) can be reached with approximately 5–20 % of thinning. Nozzle tip 0.011"–0.015" and the nozzle pressure 40–120 bar. Atomising air pressure should be about 1–3 bar. Spray angle shall be chosen according to the shape of the object.

 

Conventional application with the viscosity 20–50 s (DIN 4) can be reached with approximately 10–20 % thinning. Nozzle tip 1.4–1.8 mm and the nozzle pressure

2–3 bar.

Pot-life (+23°C) 48 hours.
Drying times

100–120 g/m²

+23ºC

+50ºC

Dry to touch, after

20–30 min

8–15 min

Dry to sand, after

1–2 h

30–40 min

 

Stacking temperature below 35ºC.

 

Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.

Содржина на цврсти материи Volume solids 57±2 %
Weight solids 73±2 %
Густина 1,4 kg/l.
Шифра на производот 691-series

ДЕТАЉИ ЗА ПРИМЕНА
Услови за примена The surface to be treated has to be clean and dry. During application and drying the temperature of the air, the surface to be treated and the primer has to be over +18ºC and the relative humidity of the air below 70%.
Припрема Wood material must be sanded with sanding paper P150–240. Sanding between primer and top coat can be done with sanding paper P240–400. All sanding dust must be removed.
Премачкување Recommended topcoats: Diccoplast 30, Diccoplast 80, Diccoplast 30 Tix and Dicco Flex 30.
Mixing of components Stir the paint carefully before use. Add 10% by volume Hardener 006 2098 and mix again carefully. Thin the paint to the viscosity required with Thinner 1027 or 1033.

Do not use iron containers as mixing container. Instead use plastic, enamel or acid resistant steel containers.
Чистење на алатот Thinner 1027 or 1033.
EU VOC 2004/42/EC ограничена вредност The Volatile Organic Compounds amount is 370 g/litre of paint.
Maximum VOC content in ready to use paint (thinned 30% by volume) is 460 g/l.
VOC 2004/42/EC (catA/j) 500 g/l (2010).

КЛАСИФИКАЦИЈА ЗА БЕЗБЕДНОСТ И ЗДРАВЈЕ
во согласност со Регулативата (EC) No. 1272/2008
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj. For industrial and professional use only.
Safety data sheetDICCOPLAST ELASTIC PRIMER [GB-ENG]
Thinner safety data sheetTHINNER 1033 [GB-ENG]
Hardener safety data sheetHARDENER 006 2098 [GB-ENG]
 
-


Назад