ТЕХНИЧКИ ЛИСТ
15.08.2012

Diccoplast Plus Tix

 
Diccoplast Plus Tix
ОПИС A two component acid catalysed primer.
КАРАКТЕРИСТИКИ НА ПРОИЗВООДОТ

A fast drying, thixotropic paint for interior use.

Good filling and sanding properties.

Перпорачана употреба Recommended for furniture, doors and other interior wooden and fibre board surfaces.

ТЕХНИЧКИ ПОДАТОЦИ
Features Thixotropic. Does not contain aromatic solvents.
Палета на бои White.
Gloss groups Matt
Emission classification The emission level of this product fulfils the requirements of E1 classification for surface treatment materials. The product has been tested according to the standard EN 717-1, and its formaldehyde emission rate is less than 0.124 mg/m3 air.
Покривност

Recommended spreading amounts (unthinned)

Theoretical coverage

dry

wet

 

40–50 µm

100–120 g/m2

11–14 m2/l

 

Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.

Разредувач 1027 and 1033
Mixing ratio Base 100 parts by volume 007 5334
Hardener 10 parts by volume 006 2098
Метод на примена

Airless application with the viscosity 25–50 s (DIN 4) can be reached with approximately 5–20 % of thinning. Nozzle tip 0.011"–0.015" and the nozzle pressure 80–180 bar. Spray angle shall be chosen according to the shape of the object.

 

Air assisted airless application with the viscosity 25–50 s (DIN 4) can be reached with approximately 5–20 % of thinning. Nozzle tip 0.011"–0.015" and the nozzle pressure 40–120 bar. Atomising air pressure should be about 1–3 bar. Spray angle shall be chosen according to the shape of the object.

 

Conventional application with the viscosity 20–50 s (DIN 4) can be reached with approximately 10–20 % thinning. Nozzle tip 1.4–1.8 mm and the nozzle pressure

2–3 bar.
Pot-life (+23°C) 48 hours.
Drying times

100120 g/m²

 

+23 ºC

+50 ºC

Dry to touch, after

20–30 min

8–15 min

Dry to sand, after

1–2 h

30–40 min

 

Stacking temperature below+ 35 ºC.

 

Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.
Содржина на цврсти материи 57±2 % by volume
73±2 % by weight
Густина 1.4 kg / litre
Шифра на производот 007 5334

ДЕТАЉИ ЗА ПРИМЕНА
Услови за примена The surface to be treated has to be clean and dry. During application and drying the temperature of the air, the surface to be treated and the primer has to be over 18 ºC and the relative humidity of the air below 70 %.
Припрема Wood material must be sanded with sanding paper P150–240. Sanding between primer and top coat can be done with sanding paper P240–400. All sanding dust must be removed with f.ex. air exhauster.
Премачкување Diccoplast 30, Diccoplast 80, Diccoplast 30 Tix and Dicco Flex.
Mixing of components Stir the paint carefullybefore use. Add 10 % by volume Hardener 006 2098 and mix again carefully. Thin the paint to the viscosity required with Thinner 1027 or 1033.

Do not use iron containers as mixing container. Instead use plastic, enamel or acid resistant steel containers.
Чистење на алатот Thinner 1027 or 1033.
EU VOC 2004/42/EC ограничена вредност The Volatile Organic Compounds amount is 390 g/litre of paint.
Maximum VOC content in ready to use paint (thinned 30 % by volume) is 490 g/l.
VOC 2004/42/EC (catA/j) 500 g/l (2010)

КЛАСИФИКАЦИЈА ЗА БЕЗБЕДНОСТ И ЗДРАВЈЕ
во согласност со Регулативата (EC) No. 1272/2008
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj. For industrial and professional use only.
Safety data sheetDICCOPLAST PLUS TIX [GB-ENG]
Thinner safety data sheetTHINNER 1033 [GB-ENG]
Hardener safety data sheetHARDENER 006 2098 [GB-ENG]
 
-


Назад