Diccoplast Primer

Diccoplast Primer
ОПИС A two component acid catalysed primer.
КАРАКТЕРИСТИКИ НА ПРОИЗВООДОТ A fast drying primer with good filling and sanding properties.
Перпорачана употреба Recommended for furniture, doors and other similar wooden and fibre board surfaces.

Палета на бои White 0201 and black 0202.
Gloss groups Matt
Emission classification Emission levels of this paint fulfils the E1-classification. Paint has been tested according to EN 717-1, and formaldehyde emission is less than 0.124 mg/m3 air.

Recommended spreading amounts (unthinned)

Theoretical coverage




40–50 µm

100–120 g/m2

11–14 m2/l


Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated

Разредувач 1027 and 1033
Mixing ratio Paint 100 parts by volume 694 serie
Hardener 10 parts by volume 006 2098
Метод на примена

Airless spraying, air assisted airless spraying and conventional spraying.


Application (+23°C)

For airless spraying, the product is thinned approximately10–20% to the viscosity

25–60s (DIN 4). Nozzle tip 0.011"–0.015" and the nozzle pressure 80–140 bar. Spray angle shall be chosen according to the shape of the object.


For air-assisted airless spraying, the product is thinned approximately 5–20% to the viscosity 25–60s (DIN 4). Nozzle tip 0.011"0.015" and the nozzle pressure 40–120 bar. Atomising air pressure should be about 1–3 bar. Spray angle shall be chosen according to the shape of the object.


For conventional spraying, the product is thinned approximately10–20% to the viscosity 25–40s (DIN 4). Nozzle tip 1.4–1.8 mm and the nozzle pressure

2–3 bar.

Pot-life (+23°C) 48 hours.
Drying times

100120 g/m²



Dry to touch, after

20–30 min

8–15 min

Dry to sand, after

1–2 h

30–40 min


Stacking temperature below +35 ºC.


Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.
Special feature Recommended topcoats: Diccoplast 30, Diccoplast 80 and Diccoplast 30 Tix.
Содржина на цврсти материи 53±2% by volume, 71±2% by weight.
Густина 1,4 kg/l.

Услови за примена The surface to be treated has to be clean and dry. During application and drying the temperature of the air, the surface to be treated and the primer has to be over +18ºC and the relative humidity of the air below 70%.
Припрема Wood material must be sanded with sanding paper P150–240. Sanding between primer and top coat can be done with sanding paper P240–400. All sanding dust must be removed.
Mixing of components Stir the paint carefully before use. Add 10% by volume Hardener 006 2098 and mix again carefully. Thin the paint to the viscosity required with Thinner 1027 or 1033.

Do not use iron containers as mixing container. Instead use plastic, enamel or acid resistant steel containers.
Чистење на алатот Thinner 1027 or 1033.
EU VOC 2004/42/EC ограничена вредност The Volatile Organic Compounds amount is 400 g/litre of paint.
Maximum VOC content in ready to use paint (thinned 20 % by volume) is 480 g/l.
VOC 2004/42/EC (catA/j) 500 g/l (2010).

во согласност со Регулативата (EC) No. 1272/2008
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj. For industrial and professional use only.
Thinner safety data sheetTHINNER 1033 [GB-ENG]
Hardener safety data sheetHARDENER 006 2098 [GB-ENG]