Fontedur FL Matt

Tikkurila Industry 9L
ОПИС A two-component, waterborne polyurethane lacquer.
КАРАКТЕРИСТИКИ НА ПРОИЗВООДОТ Suitable to be used as a top lacquer for TEMAFLOOR epoxy and polyurethene floors.
Перпорачана употреба Floors.

Features Fire Classification: BFL-s1 according to EN 13501-1.
Gloss groups Matt
Покривност Not defined. Practical coverage depends on the evenness of the substrate.
Разредувач Water
Mixing ratio Base 10 parts by volume 008 4910
Hardener 1 part by volume 008 4911
Метод на примена Trowel or roller.
Pot-life (+23°C) 5 hours.
Време на сушење на 23°C и 50% релативна влажност на воздухот

Dust dry after 40 min

Fully cured after about 1 d


At lower temperatures the curing process will last longer.
Содржина на цврсти материи 40 ± 2 volume %
Густина 1,1 kg / l
Шифра на производот 008 4910

Услови за примена The temperature of the ambient air, surface or coating should not fall below +10ºC during application or drying. Relative humidity of air should not exceed 90%.
Припрема Remove dust and loose particles from the floor. Remove all grease, oil and other impurities by detergent washing.
Премачкување Overcoating may be carried out not earlier than 16hrs after priming. If the primed surface is not overcoated within 24hrs, it should be abraded. Pour the coating mixture onto the floor and spread it with a trowel.
Mixing of components Mix the correct proportions of base and hardener thoroughly before use. Mix the correct proportions of base and hardener thoroughly (approx. 3–5 minutes) by using a low speed hand drill with a paddle. Insufficient mixing or incorrect mixing ratio will result in uneven drying of the surface, weaken the properties of the coating and risk the success of the application.
Чистење на алатот Water.
EU VOC 2004/42/EC ограничена вредност VOC 2004/42/EC (cat A/j) 140 g/l (2010)
Fontedur FL Matt: max. VOC < 140 g/l

во согласност со Регулативата (EC) No. 1272/2008
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj.
Safety data sheetFONTEDUR FL MATT [GB-ENG]
Hardener safety data sheetFONTEDUR FL MATT HARDENER [GB-ENG]

DECLARATION OF PERFORMANCE Declaration of Performance EN1504-2

The European harmonized productstandard EN 1504-2:2004 defines the requirements for surface protection systems for concrete.

This product is tested and CE-labelled in accordance with the tables 1d and 1f in the appendix ZA.
CE logo
Tikkurila Oyj
Kuninkaalantie 1
EN 1504-2:2004
[Износостойкость] puuttuu kielellä mk
< 3000 mg
[Проницаемость углекислого газа] puuttuu kielellä mk
[CO2sD > 50 m] puuttuu kielellä mk
[Водопоглощение] puuttuu kielellä mk
[w < 0,1 kg/m²∙h0,5] puuttuu kielellä mk
[Ударостойкость] puuttuu kielellä mk
[Класс I: ≥ 4 Nm] puuttuu kielellä mk
[Паропроницаемость] puuttuu kielellä mk
Class I, sD < 5 m
[Прочность на растяжение при изгибе] puuttuu kielellä mk
≥ 2,0 N/mm²
[Реакция на огонь] puuttuu kielellä mk
The above information is not intended to be exhaustive or complete. The information is based on laboratory tests and practical experience, and it is given to the best of our knowledge. The quality of the product is ensured by our operational system, based on the requirements of ISO 9001 and ISO 14001. As manufacturer we cannot control the conditions under which the product is being used or the many factors that have an effect on the use and application of the product. We disclaim liability for any damages caused by using the product against our instructions or for inappropriate purposes. We reserve the right to change the given information unilaterally without notice. The product is intended for professional use only and shall only be used by professionals who have sufficient knowledge and expertise on the proper use of the product. The information above is advisory only. To the extent permitted by applicable law, we shall not approve of any liability for the conditions under which the product is being used or for the use or application of the product. In case you intend to use the product for any other purpose than that recommended in this document without first getting our written confirmation on the suitability for the intended use, such use takes place at your own risk.