|ОПИС||A two component resin modified epoxy paint containing anti-corrosive pigments.|
|КАРАКТЕРИСТИКИ НА ПРОИЗВООДОТ||
Good adhesion to steel, zinc and aluminium surfaces. Used as a primer or an intermediate coat on surfaces exposed to climatic, mechanical and chemical stress. Pigmented with zinc phosphate.
|Перпорачана употреба||Recommended for building frameworks, tubular bridges, conveyors and other steelwork and equipment.|
|Палета на бои||Reddish brown (TVT 4000) and grey (TVT 4001).|
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.
|Mixing ratio||Base 4 parts by volume 008 7252, 7253
Hardener 1 part by volume 008 5611
Base 5 parts by volume 008 7252, 7253
Hardener 1 part by volume 008 5613
|Метод на примена||By airless or conventional spray or by brush.|
|Pot-life (+23°C)||6 hours with Hardener 008 5611
4 hours with Hardener 008 5613
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.
|Содржина на цврсти материи||72 ± 2 % (ISO 3233). Weight solids 85 ± 2 %.|
|Густина||1.4 kg / l (mixed)|
|Шифра на производот||Base 008 7252, 7253, hardener 008 5611 and hardener 008 5613|
|ДЕТАЉИ ЗА ПРИМЕНА|
|Услови за примена||All surfaces must be clean and dry. The relative humidity of the air should not exceed 80% during application and drying.
When using hardener 008 5611: the temperature of the ambient air and the substrate should be minimum +0°C and at least 3°C above the dew point of the air during application and drying.
When using hardener 008 5613: the temperature of the ambient air and the substrate should be minimum -5⁰C and at least 3°C above the dew point of the air during application and drying.
The temperature of the paint itself should be above +15°C during mixing and application.
Good ventilation and sufficient air movement is required in confined areas during application and drying.
Note! There is a natural tendency of epoxy coatings to chalk and discolor on exterior exposure
|Припрема||Oil, grease, salts and dirt are removed by appropriate means. (ISO 12944-4)
Steel surfaces: Blast clean to grade Sa2½. (ISO 8501-1) If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.
Zinc surfaces: Sweep blast clean with mineral abrasives, e.g. quartz sand, to an even roughness. (SaS, SFS 5873) If sweep blasting is not possible, the surface should be roughened by hand abrading or washed with PANSSARIPESU detergent.
Aluminium surfaces: Sweep blast clean with non-metallic abrasives to an even roughness. (SaS, SFS 5873) If sweep blasting is not possible, the surface should be roughened by hand abrading or washed with MAALIPESU detergent.
Primed surfaces: Oil, grease, salt and dirt are removed from the surface by appropriate means. Repair any damage to the primer coat. Note the overcoating time of primer. (ISO 12944-4)
|Priming||Temacoat Primer, Temazinc 77 and Temazinc 99.|
|Finishing||Temacoat GPL, Temacoat GS 50, Temacoat GPL-S MIO,
Temadur and Temathane.
|Премачкување||By airless spray or brush. At spray application the paint may be thinned 0–10% by volume when needed. Airless spray nozzle tip 0.015"–0.021" and nozzle pressure
120–180 bar. Spray angle shall be chosen according to the shape of the object.
At brush application the paint should be thinned according to the circumstancies.
|Mixing of components||First stir base and hardener separately. The correct proportions of base and hardener must be mixed thoroughly before use. Use mechanical mixer for mixing.|
|Чистење на алатот||Thinner 006 1031.|
|EU VOC 2004/42/EC ограничена вредност||The Volatile Organic Compounds amount is 280 g/litre of paint mixture.
VOC content of the paint mixture (thinned 10% by volume) is 325 g/l.
Only for industrial and professional use.
|КЛАСИФИКАЦИЈА ЗА БЕЗБЕДНОСТ И ЗДРАВЈЕ|
во согласност со Регулативата (EC) No. 1272/2008
|Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj.|
|Safety data sheet||TEMACOAT PRIMER 4000 and 4001 [GB-ENG]|
|Thinner safety data sheet||THINNER 1031 [GB-ENG]|
|Hardener safety data sheet||HARDENER 008 5611 [GB-ENG]|