ТЕХНИЧКИ ЛИСТ
04.09.2013

Temathane 50

 
Tikkurila Industry 9L
ОПИС A two component, semigloss polyurethane paint, hardener aliphatic isocyanate.
КАРАКТЕРИСТИКИ НА ПРОИЗВООДОТ Recommended to be used as a semigloss topcoat for epoxy and polyurethane systems exposed to weathering.
Перпорачана употреба Recommended for painting of outside of storage tanks, steel buildings and other steelwork.

ТЕХНИЧКИ ПОДАТОЦИ
Features Excellent weathering and abrasion resistance.
A durable, easy to clean and non-chalking topcoat with good gloss and colour retention.
Colour Cards RAL, NCS, SSG, BS, MONICOLOR NOVA, SYMPHONY, TEMASPEED Tinting
Gloss groups Semi-gloss
Покривност

Recommended film thicknesses

Theoretical coverage

dry

wet

 

40 µm

75 µm

13.7 m2/l

60 µm

110 µm

9.2 m2/l

 

Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.
Разредувач 1048, 1067 and 1061
Mixing ratio Base 9 parts by volume 514-series
Hardener 1 part by volume 008 7620
Pot-life (+23°C) 4 hours.
Drying times

DFT 50 µm

+ 5 ºC

+ 10 ºC

+ 23 ºC

+ 35 ºC

Dust dry, after

45 min

30 min

15 min

10 min

Touch dry, after

8 h

6 h

4 h

2½ h

Recoatable, after

No limitations.

 

Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.
Густина 1.2 ± 0.1 kg / l (mixed)
Шифра на производот 514-series

ДЕТАЉИ ЗА ПРИМЕНА
Услови за примена All surfaces must be dry. The temperature of the ambient air, surface or paint should not fall below +5ºC during application or drying. Relative humidity should not exceed 80%. The surface temperature of the steel should remain at least 3ºC above the dew point.
Припрема Primed surfaces: Oil, grease, salt and dirt are removed from the surface by appropriate means. Repair any damage to the primer coat. Note the overcoating time of primer. (ISO 12944-4)
Priming Temacoat GPL-S Primer, Temacoat GPL-S MIO, Temacoat RM 40, Temacoat SPA, Temabond and Temadur 20.
Finishing Temathane and Temadur.
Премачкување By airless or conventional spray or by brush. In order to obtain an even, non-porous finish, spray a misty coat: first a thin layer, then let the solvents evaporate for
5–30 minutes and then apply the full coat. Depending on the application method and the temperature of the components (base, hardener, thinner) the paint can be thinned 10–15 %. The viscosity should be 30–60 s DIN4. Airless spray nozzle tip 0.011"–0.015" and nozzle pressure 120–160 bar. Spray angle shall be chosen according to the shape of the object.

At conventional spraying the viscosity should be 20–25 s DIN4.

At brush application the paint should be thinned according to the circumstancies.
Mixing of components First stir base and hardener separately. The correct proportions of base and hardener must be mixed thoroughly before use. Use Temaspeed Squirrel Mixer for mixing.
Чистење на алатот Thinner 1048, 1067 or 1061.
EU VOC 2004/42/EC ограничена вредност The Volatile Organic Compounds amount is 425 g/litre of paint mixture.
VOC content of the paint mixture (thinned 15% by volume) is 490 g/l.

КЛАСИФИКАЦИЈА ЗА БЕЗБЕДНОСТ И ЗДРАВЈЕ
во согласност со Регулативата (EC) No. 1272/2008
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj
Safety data sheetTEMATHANE 50 [GB-ENG]
Thinner safety data sheetTHINNER 1048 [GB-ENG]
Hardener safety data sheetHARDENER 008 7620 [GB-ENG]
 
-


Назад