ТЕХНИЧКИ ЛИСТ
22.02.2010

Temazinc 77

 
Tikkurila Industry 9L
ОПИС A two component, polyamide cured zinc epoxy paint.
КАРАКТЕРИСТИКИ НА ПРОИЗВООДОТ Used as a primer in epoxy, polyurethane, acrylic and chlorinated rubber systems for steel surfaces exposed to severe climatic conditions. Can be used without a topcoat on surfaces exposed to weathering.
Перпорачана употреба Recommended for bridges, cranes and steel frameworks as well as steelwork and equipment in the forest and chemical industries, such as tubular bridges, conveyors etc.

ТЕХНИЧКИ ПОДАТОЦИ
Features Offers cathodic protection of steel. The zinc content fulfils the requirements of ISO 12944-5.
Палета на бои Grey.
Gloss groups Matt
Покривност

Recommended film thicknesses

Theoretical coverage

dry

wet

 

40 µm

75 µm

13.0 m2/l

80 µm

155 µm

6.5 m2/l


Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.
Разредувач 1031
Mixing ratio Base 3 parts by volume 008 7405
Hardener 1 part by volume 008 7440
Метод на примена By airless spray or brush.
Pot-life (+23°C) 16 hours
Drying times

DFT 40 µm

+ 5 ºC

+ 10 ºC

+ 23 ºC

+ 35 ºC

Dust dry, after

50 min

20 min

10 min

5 min

Touch dry, after

2 h

1 h

30 min

15 min

Recoatable, after

5 h

3 h

1 h

30 min


Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation.
Содржина на цврсти материи 52 ± 2 % volume (ISO 3233)
Густина 2.0 kg / l (mixed)
Шифра на производот 008 7405

ДЕТАЉИ ЗА ПРИМЕНА
Услови за примена All surfaces must be dry. The temperature of the ambient air, surface or paint should not fall below +5 ºC during application and drying. Relative humidity should not exceed 80 %. The surface temperature of the steel should remain at least 3 ºC above the dew point.
Припрема Oil, grease, salts and dirt are removed by appropriate means. (ISO 12944-4)

Steel surfaces: Blast clean to grade Sa2½. (ISO 8501-1)
Finishing Temacoat GPL-S Primer, Temacoat GF Primer, Temacoat HB Primer, Temacoat GPL-S MIO, Temacoat GS 50, Temacoat RM 40, Temacoat HB 30, Temacoat SPA, Temabond, Temachlor 40, Temacryl AR 50 and Temanyl MS Primer.
Премачкување By airless spray or brush. Agitate during application. Depending on the application method the paint can be thinned 0 - 10 % by volume. Airless spray nozzle tip 0.015" - 0.021" and nozzle pressure 120 - 180 bar. Spray angle shall be chosen according to the shape of the object. Sharp edges, corners, weld seams and other areas difficult to cover properly by spray application should be coated by brush before the spray application. At brush application the paint should be thinned according to the circumstancies.
Mixing of components First stir base and hardener separately. The correct proportions of base and hardener must be mixed thoroughly before use. Use Temaspeed Squirrel Mixer for mixing.
Чистење на алатот Thinner 1031.
EU VOC 2004/42/EC ограничена вредност The Volatile Organic Compounds amount is 480 g/litre of paint.
VOC content of the paint mixture (thinned 5 % by volume) is 495g/l.
Only for industrial use.

КЛАСИФИКАЦИЈА ЗА БЕЗБЕДНОСТ И ЗДРАВЈЕ
во согласност со Регулативата (EC) No. 1272/2008
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets. A health and safety data sheet is available on request from Tikkurila Oyj.
Safety data sheetTEMAZINC 77 [GB-ENG]
Thinner safety data sheetTHINNER 1031 [GB-ENG]
Hardener safety data sheetHARDENER 008 7440 [GB-ENG]
 
-


Назад